13 Types of Cement and their Uses

13 Cements:-

  1. Ordinary Portland Cement (OPC)
  2. Portland Pozzolana Cement (PPC)
  3. Rapid Hardening Cement
  4. Quick setting cement
  5. Low Heat Cement
  6. Sulfates resisting cement
  7. Blast Furnace Slag Cement
  8. High Alumina Cement
  9. White Cement
  10. Colored cement
  11. Air Entraining Cement
  12. Expansive cement
  13. Hydrographic cement
Types of Cement and their Uses
 Cement

1. Ordinary Portland Cement (OPC)

Ordinary Portland cement is the most widely used type of cement, which is suitable for all general concrete construction. It is the most commonly produced and used type of cement around the world, with annual global production of around 3.8 million cubic meters per year.  This cement is suitable for all kinds of concrete construction.

2. Portland Pozzolana Cement (PPC)

Portland pozzolana cement is prepared by grinding pozzolanic clinker with Portland cement. It is also produced by adding pozzolana with the addition of gypsum or calcium sulfate or by intimately and uniformly blending Portland cement and fine pozzolana.

This cement has a high resistance to various chemical attacks on concrete compared with ordinary portland cement, and thus, it is widely used. It is used in marine structures, sewage works, sewage works, and for laying concrete underwater, such as bridges, piers, dams, and mass concrete works, etc.

3. Rapid Hardening Cement

Rapid hardening cement attains high strength in the early days; it is used in concrete where formworks are removed at an early stage and are similar to ordinary portland cement (OPC). This cement has increased lime content and contains higher c3s content and finer grinding, which gives higher strength development than OPC at an early stage.

The strength of rapid hardening cement at the three days is similar to 7 days strength of OPC with the same water-cement ratio. Thus, the advantage of this cement is that formwork can be removed earlier, which increases the rate of construction and decreases the cost of construction by saving formwork cost.

Rapid hardening cement is used in prefabricated concrete construction, road works, etc.

4. Quick setting cement

The difference between the quick setting cement and rapid hardening cement is that quick-setting cement sets earlier. At the same time, the rate of gain of strength is similar to Ordinary Portland Cement, while quick hardening cement gains strength quickly. Formworks in both cases can be removed earlier.

Quick setting cement is used where works is to be completed in very short period and for concreting in static or running water.

5. Low Heat Cement

Low heat cement is produced by maintaining the percentage of tricalcium aluminate below 6% by increasing the proportion of C2S. A small quantity of tricalcium aluminate makes the concrete to produce low heat of hydration. Low heat cement suitable for mass concrete construction like gravity dams, as the low heat of hydration, prevents the cracking of concrete due to heat.

This cement has increased power against sulphates and is less reactive and initial setting time is greater than OPC.

6. Sulfates Resisting Cement

Sulfate resisting cement is used to reduce the risk of sulfate attack on concrete and thus is used in the construction of foundations where the soil has high sulfate content. This cement has reduced the contents of C3A and C4AF.

Sulfate resisting cement is used in construction exposed to severe sulfate action by water and soil in places like canals linings, culverts, retaining walls, siphons, etc.

7. Blast Furnace Slag Cement

Blast furnace slag cement is obtained by grinding the clinkers with about 60% slag and resembles more or less in properties of Portland cement. It can be used for works where economic considerations are predominant.

8. High Alumina Cement

High alumina cement is obtained by melting a mixture of bauxite and lime and grinding with the clinker. It is a rapid hardening cement with initial and final setting time of about 3.5 and 5 hours, respectively.

The compressive strength of this cement is very high and more workable than ordinary portland cement and is used in works where concrete is subjected to high temperatures, frost, and acidic action.

9. White Cement

It is prepared from raw materials free from Iron oxide and is a type of ordinary portland cement, which is white. It is costlier and is used for architectural purposes such as precast curtain wall and facing panels, terrazzo surface, etc. and for interior and exterior decorative work like external renderings of buildings, facing slabs, floorings, ornamental concrete products, paths of gardens, swimming pools, etc.

10. Colored cement

It is produced by mixing 5- 10% mineral pigments with ordinary cement. They are widely used for decorative works on floors.

11. Air Entraining Cement

Air entraining cement is produced by adding indigenous air-entraining agents such as resins, glues, sodium salts of sulfates, etc. during the grinding of clinker.

This type of cement is especially suited to improve the workability with a smaller water-cement ratio and to improve frost resistance of concrete.

12. Expansive Cement

Expansive cement expands slightly with time and does not shrink during and after the time of hardening. This cement is mainly used for grouting anchor bolts and prestressed concrete ducts.

13. Hydrographic cement

Hydrographic cement is prepared by mixing water-repelling chemicals and has high workability and strength. It has the property of repelling water and is unaffected during monsoon or rains.

Hydrophobic cement is mainly used for the construction of water structures such as dams, water tanks, spillways, water retaining structures, etc.

Comments

Post a Comment

Popular posts from this blog

Types of Bricks in Masonry Construction – Properties & Uses

Image
D ifferent types of bricks are used in masonry construction based on material such as clay, concrete, lime, fly ash etc. Filed field identification of bricks for their properties, uses and suitability for different construction works are important.    Sun-Dried or Unburnt Clay  After molding, bricks are subjected to sunlight and dried using heat from sun. So, they are not that much strong and they also have less water resistance and less fire resistance. These bricks are not suitable for permanent structures. 2. Burnt Clay Bricks First class bricks Second class bricks Third class bricks Fourth class bricks First Class Bricks First class bricks are good quality bricks compared to other classes. They are molded by table-molding and burnt in large kilns. So, these bricks contain standard shape, sharp edges and smooth surfaces. They are more durable and having more strength. They can be used for permanent structures. However, because of their good properties they are costly than other clas
Read more

CONCRETR AND THEIR USAGES

Image
                                                                               Fresh Concrete          An artificial stone-like material used for various structural purposes. It is made by mixing cement and various aggregates, such as sand, pebbles, gravel, shale, etc., with water and allowing the mixture to harden by hydration. Portland cement is the mostly used cement for the production of  concrete . It is the most popular artificial material. Probably It is used more than any other man-made product in the world. Usages of Concrete:   Cement is probably the most used man-made material. Concrete is used to make:       Pavements      architectural structures      foundations      motorways      roads and bridges      overpasses      parking structures      walls and footings for gates      fences and poles                                                                                                     
Read more

SAND USED IN CONSTRUCTION AND THEIR CLASSIFICATION

Image
Sand  is a mixture of small grains of rock and granular materials which is mainly defined by size, being finer than gravel and coarser than silt. And ranging in size from  0.06 mm to 2 mm . Particles which are  larger than 0.0078125 mm  but  smaller than 0.0625 mm are termed  silt . Sand is made by erosion or broken pebbles and weathering of rocks, which is carried by seas or rivers. And freezing and thawing during the winter break rock up the sand will be made. Sometimes Sand on beaches can also be made by small broken-up pieces of coral, bone, and shell, which are broken up by predators and then battered by the sea, and even tiny pieces of glass from bottles discarded in the sea and other mineral materials or the bones of fishes or other oceanic animals. Sand can be also considered as a textural class of soil or soil type. A  sandy soil  containing more than 85 percent sand-sized particles by mass. Followings are the classification of Sand:   Based on the grain size of the particle,
Read more